How To Fix Electronic Throttle Control On Jeep Patriot? The electric throttle control came on and so did the electronic stabilty control. We also could turn ours off and back on. It would make a temporay fix, and then. Put old throttle body back in after cleaning it up a bit (though it didn't look very dirty) Reverted to same behavior prior to installing new throttle body (periodic. The dealer replaced the throttle body and throttle position sensor, the powertrain control module, and the gas pedal assembly and sensor. NONE of these. When it first happened, it was going down the highway, the ETC light came on, then check engine, then the car entered limp mode. When it was safe, I pulled off to.
An Electronic Throttle Control (ETC) is an important part of the operation of a Jeep Patriot. It is responsible for controlling how much fuel is released into the engine, and is responsible for providing the power required to move the vehicle. When the ETC is not functioning properly, it can cause the vehicle to experience a range of problems including poor performance, rough idling, and even stalling. In order to ensure that your Jeep Patriot is properly functioning, it is important to learn how to fix an Electronic Throttle Control (ETC) on a Jeep Patriot.
The first step in fixing an Electronic Throttle Control (ETC) on a Jeep Patriot is to check the wiring harnesses. The wiring harnesses connect the throttle body to the ETC, and any damage or corrosion to the wiring can cause the ETC to malfunction. If any damage or corrosion is present, it should be repaired or replaced immediately.
The next step is to check the throttle body for any debris or buildup. If there is an accumulation of dirt or debris, it should be removed with a vacuum or a suitable cleaner. It is also important to ensure that the throttle plate is properly adjusted, and that the butterfly valve is in the correct position.
The third step is to inspect the throttle position sensor (TPS). The TPS is responsible for sending a signal to the ETC when the driver presses down on the accelerator pedal. If the TPS is not functioning properly, it can cause the ETC to malfunction. The TPS should be tested using a multimeter and the appropriate readings should be taken to confirm that it is functioning correctly. If the TPS is not functioning correctly, it should be replaced.
The fourth step is to check the Electronic Throttle Control (ETC) for any damage or contamination. If any damage or contamination is present, it should be repaired or replaced. It is also important to ensure that the ETC is properly calibrated, and that it is functioning properly.
The fifth step is to check the throttle body for any air leaks. If there are any air leaks present, they should be sealed. It is also important to ensure that the throttle body is properly lubricated, and that the gaskets are in good condition.
The sixth step is to inspect the fuel injectors for any damage or contamination. If any damage or contamination is present, it should be repaired or replaced. It is also important to ensure that the injectors are functioning properly and that they are providing the correct amount of fuel to the engine.
The seventh step is to check the vacuum lines for any damage or contamination. If any damage or contamination is present, it should be repaired or replaced. It is also important to ensure that the vacuum lines are properly connected, and that they are providing the correct amount of vacuum to the engine.
The eighth step is to check the Electronic Throttle Control (ETC) for any software issues. If any software issues are present, they should be addressed immediately. It is also important to ensure that the ETC is properly updated, and that it is functioning properly.
By following these steps, you should be able to fix an Electronic Throttle Control (ETC) on a Jeep Patriot. If any of the components are damaged, corroded, or malfunctioning, it is important to have them repaired or replaced as soon as possible. Doing so will help ensure that your Jeep Patriot is running at its optimal performance.
2016 Jeep Patriot Throttle Relearn
After installing the throttle body there is a a simple relearn process.
After down shifting to 3rd I recovered and slowly accel until the Pat top out at 65 mph, and would not go any faster. After shifting to 5th or accel above 65 the power.